Skip to main content

Full text of "Revotech Industries RETRT600-1 user manual"

See other formats


Operating Manual 


USER'S INSTRUCTIONS 




Model No.: RETRT600-1 

(DC 12V — /AC 24V ~ 60HZ, 12W / NTSC) 
REVO AMERICA 

700 FREEPORT PARKWAY SUITE 100 COPPELL, 
TX 75019 U.S.A. TEL.: 1-866-625-REVO(7386) 

























4 


USER’S MANUAL 


Al 


CAUTION 


A 



CAUTION : 


TO REDUCE THE RISK OF ELECTRIC SHOCK, 
DO NOT REMOVE COVER (OR BACK), 

NO USER SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED 
SERVICE PERSONNEL 


The lightning flash with an arrowhead symbol, within an equilateral 
triangle is intended to alert the user to the presence of uninsulated 
dangerous voltage within the product's enclosure that may be of 
sufficient magnitude to constitute a risk of electric shock to persons. 

The exclamation point within an equilateral triangle is intended to alert 
the user to the presence of important operating and maintenance 
(servicing) instructions in the literature accompanying the appliance. 


INFORMATION - This equipment has been tested and found to comply with 
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instruction manual, may 
cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interfer¬ 
ence at his own expense. 

WARNING - Changes or modifications not expressly approved by the 
manufacturer could void the user's authority to operate the equipment. 

WARNING - To prevent electric shock and risk of fire hazards: 

♦ Do NOT use power sources other than that specified. 

♦ Do NOT expose this appliance to rain or moisture. 


RoHS C€ F© © 


This installation should be made by a qualified service person and 
should conform to all local codes. 


2 











USER’S MANUAL 


Contents 

(J General Features. 4 

3 Installing & Adjusting. 5 

(J Dimension & Specification . 6 

3 OSD Control Button. 7 

(J Camera Menu Set Up 

1. Menu Set Up. 8 

2. Lens Setting. 8 

3. Exposure Setting. 9 

4. White Balance Setting. 10 

5. SSDR Setting. 11 

6. Backlight Setting . 12 

7. DNR3 Setting. 13 

8. Day/Night Setting. 14 

9. Special Setting. 15 

10. Exit Setting. 19 

3 Trouble Shooting. 20 


3 






















USER’S MANUAL 


General Features 


0 Ultra High Sensitivity 

- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON) 
or lower illumination. 

3 600TV Lines 

- By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, 
the camera produces clear picture quality with a horizontal resolution of 600 TV lines for 
color and a horizontal resolution of 700TV lines for BW mode. 

3 DNR3 

-The high-performance W-V DSP chip effectively removes low-light gain noise and ghosting to 
provide clear images even in dark environments. 

3 Day & Night 

- This camera has a function that automatically selects the mode that is appropriate for 
daytime or night-time conditions. The COLOR mode operates in daytime conditions to 
provide optimum colors, and BW mode operates in night-time conditions to enhance the 
definition of the image. 

3SSDR 

- For images with high contrast between bright and dark Areas from difficult lighting conditions 
such as backlighting, this camera selectively illuminates darker Areas while retaining the same 
light level for brighter Areas to even out the overall brightness. 

3 Miscellaneous Functions 

- HLC(High Light Compensation), SENS-UP, FLIP(HA/-REV), D-ZOOM, SHARPNESS, MOTION 
DETECTION and PRIVACY functions are provided. 

3 Disk Saving Effects 

- Up-most and advanced DNR technology camera picture quality has a disk saving effects due to 
Image sizes are smaller than standard CCTV camera image. 

3 Controlled by OSD Menu 

- The camera can be controlled by selecting the menu text displayed on the monitor screen. 

3 IP66 Approved / Vandal Proof / RoHS Compliance 

- To prevent from external strong impact. It has a high strength and durable exterior material of die 
cast aluminum body. It also has designed to prevent from shock, dust and rain resistant. The 
turret camera has designed to install anywhere even at exterior places. 


4 







USER’S MANUAL 


INSTALLING & ADJUSTING 


1. Installation 



- Place the mounting plate on a flat installation surface 
and mount with the provided screws. 

- Feed the cable through the center of the mounting plate. 

- Place the camera body in the mounting plate socket 
and hold. 

- Then place the outer plate over the camera body & 
mounting plate and tighten side screws to lock the 
camera into place. 

- Loosen side screws to adjust camera angle as needed, 
then tighten the side screws to lock into place. 


2. Focus/Zoom Screw 

- To widen the viewing angle turn the Zoom screw 
to "W"(Wide) to obtain a closer view turn it to 
H T"(Tele) 

- Turn the Focus screw to "N"(Near) or "°o" 
(Far) untill the sharpest Focus is made. 



5 































































USER’S MANUAL 


DIMENSION & SPECIFICATION 


1. Dimension & Connection 

Dimension 





2. Specification 


Image Pick-Up Device 

1/3" Sony Super HAD CCD 

TV System 

NTSC 

Total Pixels 

811(H) * 508(V) 

Effective Pixels 

768(H) * 494(V) 

Scanning Frequency 

1 5.734KHz(H) & 59.94Hz(V) 

Scanning System 

2:1 Interlace 

Synchronization 

Internal / Line Lock 

Resolution 

600TV Lines 

Minimum Illumination 

IR LED OFF: 0.15 Lux, IR LED ON: 0.00002 Lux 

S/N Ratio 

More than 52dB 

Video Output 

CVBS: 1.0Vp-p / 750 

Electronic Shutter Speed 

NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) 

OSD 

Available 

SSDR 

On / Off (Level adjustable) 

BLC 

BLC / HLC/OFF 

Day & Night 

Color / BW/AUTO 

Gain Control 

Low / High / Off 

White Balance 

ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 1 1,000°K) 

SENS-UP 

Auto / Off (Selectable x2 ~ x51 2) 

Motion Detection 

On / Off (8 Programmable Zones) 

Privacy Masking 

On / Off (12 Programmable Zones) 

DNR3 (Digital Noise Reduction) 

On / Off (Level adjustable) 

Digital Zoom 

On / Off (x 1 ~ xl 6) 

DIS (Digital Image Stabilizadion) 

On/Off 

Sharpness 

On / Off (Level adjustable) 

Filp/ Mirror 

On/Off 

Power Supply 

DC 1 2V / AC 24V Dual Voltage 

Power Consumption 

IR LED OFF 200mA(DC), IR LED OFF 70mA(AC) / IR LED ON 670mA(DC), IR LED ON 240mA(AC) 

Lens 

DC Auto Iris Varifocal Lens(6mm-50mm) 

Operational Temp. 

-10 ~ +50 Deg C. RH95% MAX. 

Storage Temp. 

-20 ~ +60 Deg C. RH95% MAX. 

Dimension 

140mm(W) * 111 mm(H) * 1 80mm(D) 

Weight 

1800g 


6 











































































USER’S MANUAL 


OSD Control Button 


1. OSD button could be used when it needs to OSD control. 



A Up button: Moves the cursor upwards. Use this button to select an item 
or adjust the parameters. 

▼ Down button: Moves the cursor downwards. Use this button to select an 
item or adjust the parameters. 

◄ Left button: Moves the cursor to the left. Use this button to select or 
adjust the parameters of the selected item. The parameter changes 
each time this button is pressed. 

► Right button: Moves the cursor to the right. Use this button to select or 
adjust the parameters of the selected item. The parameter changes each 
time this button is pressed. 

© Set button: Executes selections and displays a submenu for an item with 
the 53 mark. 


7 








USER’S MANUAL 


• Menu Setup 

1. Press the Function Setup switch. 

- Main setup menu is displayed on the monitor screen. 


MAIN SETUP 

► 1.LENS 

DC 4- 1 

2.EXPOSURE 4- 1 


3.WHITE BAL 

ATW 

4.SSDR 

OFF 

5.BACKLIGHT 

OFF 

6.DNR3 

ON 4-* 

7.DAY/NIGHT 

AUTO 4- 1 

8.SPECIAL 4-1 


9. EXIT 

SAVE 


2. Select a desired function using the Function Setup switch. 

- Place the cursor over a desired item. 

3. Set up a selected item by using the Function Setup switch. 

4. To finish the setting, select 'EXIT' and press the Function Setup switch. 

NOTE 

■ An item with the ^ icon also has sub menus. To select a sub menu, select an item 
with the icon and press the Function Setup switch. 

■ An item with the — icon is unavailable due to function settings. 


• Lens Setting 


Using this function, you can control the screen brightness. 

1. When the SETUP menu screen is displayed, select 'LENS' by 
the Function Setup switch so that the arrow indicates 'LENS'. 

2. DC : You can adjust the minimum shutter and maximum value 
shutter mode. 


MAIN SETUP 

► 1.LENS 

DC 4- 1 

2.EXPOSURE 4-1 


3.WHITE BAL 

ATW 


using 
of ESC 


3. THE Lens mode has sub menu items as listed below. 
- BRIGHTNESS : Adjusts the video brightness. 


8 










USER’S MANUAL 


- FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings 
mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and 
then deactivate the settings mode. 

up NOTE 

■ If color rolling occurs when using a DC lens, set Shutter to Fixed (—). 

• Exposure Setting 


MAIN SETUP 

1.LENS 

DC 

► 2.EXPOSURE ◄-< 


3.WHITE BAL 

ATW 


1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the 
Function Setup Switch. 

2. Select a desired mode using the Function Setup switch. 


EXPOSURE SETUP 


► 1.BRIGHTNESS . 

in 25 

2.SHUTTER 

— 

3.AGC 

HIGH 

4.SENS-UP 

OFF 

5.RETURN 4- 1 



* SHUTTER : You can select either auto or manual shutter. 

* ---: Shutter speed is fixed at 1/60sec(1/50sec) 

* ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter 
speed is automatically controlled depending on the ambient illumination of the subject. 

* MANUAL: You can control shutter speed manually. 

(NTSC MODEL: 1/60-1/120,000, PAL MODEL: 1/50-1/120,000) 

* A.FLK: Select this when you see picture flicker, this can happen when the frequency of the 
local lighting clashes with the camera. 


NOTE 

■ When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled. 


9 












USER’S MANUAL 


* AGC(AUTO GAIN CONTROL): The higher the gain level, the brighter the screen 
but the higher the noise. 

* OFF : Deactivates the AGC function. 

* LOW: Allows automatic gain control from 5.3dB to 32dB. 

* HIGH : Allows automatic gain control from 5.3dB to 37dB. 

* SENS-UP: When it is night or dark, the camera automatically detects the light 
level and maintains a clear picture if this mode is activated. 

* OFF : Deactivates the SENS-UP function. 

* AUTO : Activates the SENS-UP function. 

* RETURN : Select this to save the changes in the EXPOSURE menu and 
return to the SETUP menu. 


NOTE 

■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by 
increasing or decreasing the shutter speed. (x2 ~ x512) 

■ Note that the higher the zoom level, the brighter the screen, but the more likely there 
will be a ghosting effect. 

■ It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when 
the D-ZOOM level is increased. 


• White Balance (White Bal) Setting 

Use the White Balance function to adjust the screen color. 

1. When the SETUP menu screen is displayed, select 'White Bal' by using the Function 
Setup switch so that the arrow indicates 'White Bal'. 

2. Select a desired mode using the Function Setup switch. 


MAIN SETUP 

1.LENS 

DC ◄-> 

2.EXPOSURE 


► 3.WHITE BAL 

ATW 


10 









USER’S MANUAL 


Select one of the following 5 modes, as appropriate for your purpose. 

♦ ATW: Select this when the color temperature is between 1,700°K and 11,000°K. 

♦ OUTDOOR: Select this when the color temperature is between 1,700°K and 11,000°K. 

(sodium light inclusion) 

♦ INDOOR: Select this when the color temperature is between 4,500°K and 8,500°K. 

♦ MANUAL: Select this to fine-tune White Balance manually. Set White Balance first by using the 
ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and then press 
the Function Setup switch. 

♦ AWC->SET: To find the optimal luminance level for the current environment, point the 
camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, 
readjust it. 

NOTE 

■ White Balance may not work properly under the following conditions. In this case 
select the AWC mode. 

© When the color temperature of the environment surrounding the subject is out of the 

control range (e.g. clear sky or sunset). 

d) When the ambient illumination of the subject is dim. 

(3) If the camera is directed towards a fluorescent light or is installed in a place where 
illumination changes dramatically, the White Balance operation may become unstable. 

♦ SSDR Setting 

SSDR illuminates darker spots of an image while retaining the same light level for brighter 
spots to even out the overall brightness of images with high contrast between bright and 
dark spots. 


MAIN SETUP 

1.LENS 

DC 

2.EXPOSURE ◄-> 


3.WHITE BAL 

ATW 

► 4.SSDR 

OFF 


1. When the SETUP menu screen is displayed, select 'SSDR' by using the switch so 
that the arrow indicates 'SSDR'. 

2. Use the switch to change the SSDR level according to the contrast between bright 
and dark areas. 


11 









USER’S MANUAL 


• Backlight Setting 

Unlike conventional cameras, W-V chip camera is designed to deliver a distinctive subject 
and background at the same time, even when the subject is backlight, by using the features 
of the proprietary W-V DSP chip. 

1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function 
Setup switch so that the arrow indicates 'BACKLIGHT'. 


MAIN SETUP 

1.LENS 

DC 4- 1 

2.EXPOSURE ◄-> 


3.WHITE BAL 

ATW 

4.SSDR 

OFF 

► 5.BACKLIGHT 

OFF 

6.DNR3 

ON 

7.DAY/NIGHT 

AUTO 4- 1 

8.SPECIAL 4J 


9. EXIT 

SAVE 


2. Select a desired mode using the Function Setup switch. 

♦ BLC : Enables a user to directly select a desired area from a picture, and to view 
the area more clearly. 

♦ HLC (High Light Compensation): If the scene contains extremely bright light areas 
such as; from car headlights, the light can mask out much of the on-screen detail 

- LEVEL: Adjust level of the HLC function. 

- LIMIT: Enable to change the operating condition. 

- MASK COLOR/TONE : Change the color / transparency of the masking area. 

(Black, Red, Blue, Cyan, Magenta) 

- TOP/BOTTOM/LEFT/RIGHT: Adjust the area to be enhanced 

♦ OFF : Not being used 


3. Select a desired mode using the Function Setup switch and press the Function Setup switch. 

♦ Select 'BLC' to adjust the area to be ♦ Select 'HLC' to adjust the area to be 

enhanced then adjust the level. enhanced then adjust the level. 


12 







USER’S MANUAL 




BLC SETUP 


► LEVEL 


LOW 

TOP 

ii|iiiiiiiiiiiiiiiiiiiiiii 

38 

BOTTOM 

iiiiiiiiiiiiiiiiiiiiiii|ii 

109 

LEFT 

ii|iiiiiiiiiiiiiiiiiiiiiii 

54 

RIGHT 

iiiiiiiiiiiiiiiiiiiii|iiii 

121 

Press Set to Return 



HLC SETUP 


► LEVEL 

MIDDLE 


LIMITS 

NIGHT ONLY 

MASK COLOR 

BLACK 


MASK TONE i|n 

iiiiiiiiiiiiiiiiiiiiii 

i 

TOP |m 

iiiiiiiiiiiiiiiiiiiiii 

5 

BOTTOM mi 

iiiiiiiiiiiiiiimm|m 

120 

LEFT Im 

iiiiiiiiiiiiiiiiiiiiii 

5 

RIGHT mi 

iiiiiiiiiiiiiiiiiiiiii 

172 

Press Set to Return 



NOTE 

■ Because there can be a difference in the effectiveness of HLC according to the amount 
of light area in the screen, optimize the installation angle for the best HLC performance. 

■ When dark, the HLC is only activated when a bright light exceeding a specific size in 
NIGHT ONLY mode. 

■ The HLC is not activated in day light or when bright light is not present at night in NIGHT 
ONLY mode. 

■ BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu. 


• DNR3 Setting 

This function reduces the background noise in a low luminance environment. 

1. When the SETUP menu screen is displayed, select 'DNR3' by using the Function 
Setup switch so that the arrow indicates 'DNR3'. 


MAIN SETUP 

1.LENS 

DC 4- 1 

2.EXPOSURE 4J 


3.WHITE BAL 

ATW 

4.SSDR 

OFF 

5.BACKLIGHT 

OFF 

► 6.DNR3 

ON 4- 1 

7.DAY/NIGHT 

AUTO 4- 1 

8.SPECIAL 


9. EXIT 

SAVE 


2. Select a desired mode using the Function Setup switch. 

♦ OFF : Deactivates DNR3. Noise is not reduced. 

♦ ON : Activates DNR3 so that noise is reduced. 


13 

































USER’S MANUAL 


3. Set the DNR3 mode to 'ON' and press the Function Setup switch. Then you 
can adjust the noise reduction level. 

NOTE 

■ You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. 

■ When adjusting the noise reduction level in the DNR3 mode, remember that the higher the 
level set, the more the noise level will be reduced, as will the brightness of the image. 


• Day/Night Setting 

You can display pictures in color or black and white. 

1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the Function 
Setup switch so that the arrow indicates 'DAY/NIGHT'. 


MAIN SETUP 

1.LENS 

DC 

2.EXPOSURE 


3.WHITE BAL 

ATW 

4.SSDR 

OFF 

5.BACKLIGHT 

OFF 

6.DNR3 

ON 

► 7.DAY/NIGHT 

AUTO ◄-* 

8.SPECIAL 


9. EXIT 

SAVE 


2. Select a desired mode using the Function Setup Switch according to the picture 
display you want. 

♦ COLOR : The picture is always displayed in color. 

♦ B/W : The picture is always displayed in black and white. 

- BURST MODE : You can turn on or off the burst signal on B/W mode. 


B/W MODE SETUP 

► 1.BURST MODE ON 

2. RETURN 


14 










USER’S MANUAL 


♦ AUTO: The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode 


when ambient illumination is low. To set up the switching time for AUTO mode, press the Function 


Setup switch. You can turn on or off the burst signal on B/W mode. 


- BURST MODE: You can turn on or off the burst signal 
on B/W mode. 

- DURATION: You can select brightness of illumination 
about changing the day/night mode. 

- DWELLTIME: You can select the duration time about 
changing the day/night mode. 

->3s, 5s, 7s, 10s, 15s, 20s, 30s, 40,60s 


AUTO SETUP 

► 1.BURST MODE 

ON 

2.COLOR-+B/W 


DURATION 

FAST 

DWELLTIME 

3SEC 

3.B/W-+COLOR 


DURATION 

FAST 

DWELLTIME 

10SEC 

4.RETURN ◄-* 




COLOR—>B/W 

B/W—>COLOR 

FAST 

2.5 lux 

5 lux 

SLOW 

1 lux 

10 lux 


* The day/night switching point of the 
camera can be adjusted. 


NOTE 

■ When AGC in the EXPOSURE menu is 'OFF',mode operates as like selecting 'COLOR' 
mode and 'AUTO' mode can not be selected. 


• Special Setting 

1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup 
switch so that the arrow indicates 'SPECIAL'. 


MAIN SETUP 

1.LENS 

DC 

2.EXPOSURE 


3.WHITE BAL 

ATW 

4.SSDR 

OFF 

5.BACKLIGHT 

OFF 

6.DNR3 

ON 4- 1 

7.DAY/NIGHT 

AUTO 

► 8.SPECIAL «-■ 


9. EXIT 

SAVE 


15 
















USER’S MANUAL 


2. Select a desired mode using the Function Setup switch. 


SPECIAL 


► 1.IMAGE ADJ 

2.MONITOR 

LCD4J 

3.CAM TITLE 

OFF 

4.SYNC 

INT 

5.MOTION DET 

OFF 

6.PRIVACY 

OFF 

7.LANGUAGE 
9.RETRUN 4-> 

ENGLISH 


♦ IMAGE ADJ.: 

1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the 
Function Setup switch so that the arrow indicates 'IMAGE ADJ'. 

2) Select a desired mode using the Function Setup switch. 


IMAGE SETUP 

► 1.V-REV 

2. H-REV 

OFF 

3. D-ZOOM 

OFF 

4.DIS 

OFF 

5.FONT COLOR 

WHITE 

6.SHARPNESS 
7.RETURN 4-* 

ON 4-1 


* V-REV: You can flip the picture vertically on the screen. 

* H-REV : You can flip the picture horizontally on the screen. 

* D-ZOOM : You can use a digital zoom of xl ~ x16. 

* FONT COLOR: You can change the OSD font color. (White, Yellow, Green, Red, Blue) 

* SHARPNESS: As you increase this value, the picture outline becomes stronger and clearer. 
Adjust this value appropriately depending on the sharpness of the picture. 

* DIS (Digital Image Stabilizer): 

This function mitigates any picture movement due to external factors such as wind. 

NOTE 

■ As the DIS function uses the digital zoom the camera's resolution will decrease. 

■ DIS doesn’t operate when background illumination is too low. 

■ DIS doesn’t operate when object pattern is monotonic as like sky or white wall. 


* RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP 
menu. 


16 










USER’S MANUAL 


NOTE 

■ When the V-REV or H-REV mode is enabled, the text on the screen does not flip. 

■ If you increase the SHARPNESS level too high, the picture may become distorted or noise 
may appear. 


that the 


CAMERA TITLE SETUP 
ABCDEFGHI JKLM 
NOPQRSTUVWXYZ 
abcdefghijklm 
nopqrstuvwxyz 
-.0123456789 


♦ CAM TITLE : If you enter a title, the title will appear on the monitor. 

1) If the SPECIAL menu screen is displayed, use the Function Setup switch so 
arrow indicates 'CAM TITLE'. 

2) Set it to 'ON' by using the Function Setup switch. 

3) Press the Function Setup switch. 

4) Use the Function Setup switch to move to a 
desired letter and select the letter by pressing 
the Function Setup switch. Repeat this to enter 
multiple letters. You can enter up to 15 letters. 

5) Enter a title, move the cursor to 'POS' and 
press the Function Setup switch. The entered 
title appears on the screen. Select the position 
to display the title on the screen by using the 
Function Setup switch and press the Function 
Setup switch. When the position is determined, 
select 'END' and press the Function Setup switch 
to return to the SPECIAL menu. 


►CLR POS 


END 



NOTE 

■ When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if 
you enter one. 

■ Only English is available in this mode. 

■ If you move the cursor to CLR and press the Function Setup switch, all the letters are 
deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function 
Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be 
inserted and then press the Function Setup switch. 

* SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the 
output phase of multiple cameras using the power synchronization function (Line-Lock) without 
using a synchronization signal generator. 

- INT: Internal Synchronization Type 

- Ill : Power Synchronization Type, Line-lock(AC24V Power) 

* Press the Function Setup switch. 

* You can select a desired phase from 0 to 359 when select 'phase'. 


17 




















USER’S MANUAL 


NOTE 

■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type 
synchronization. 

■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode. 


♦ MOTION DET :This product has a feature that 
allows you to observe movement of objects in 8 
different areas on the screen, and the words 
'MOTION DETECTED' appear on the screen when 
movement is detected. 

Activity can be monitor more efficiently. 

1) When the SPECIAL menu screen is displayed, 
press the Function Setup switch so that the arrow 
indicates'MOTION DET’. 

2) Set up the mode using the Function Setup switch. 

- SENSITIVITY: You can select up to 8 MD areas. When SENSITIVITY number is high, motion 
detection sensitivity is increased to recognize even small movement. 

- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY. 

- SEL POS : Determines which of the 4 vertices of each MD area is to be used. 

- XPOS : Determines the coordinate of the horizontal axis for SEL POS. 

- YPOS : Determines the coordinate of the vertical axis for SEL POS. 

- FILL^SET: Fills in a selected MD area. The color of the area can be selected from brown, orange, 
blue, cyan, green, yellow, magenta and red. 

- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu. 


MOTION DET 


1.SENSITIVITY 

AREA1 

2.AREA MODE 

ON 

3.SEL POS 

L-TOP 


4. XPOS ii|iiiiiiiiiiiiiiiiiiiiiii 3 

5. YPOS iiiiiiiiiiiiiiiiiiiiiiiMi r 5 

6 . FILL -»■ SET 

7. RETRUN 


♦ PRIVACY : Mask an area you want to hide on the screen. 


PRIVACY AREA SETUP 

► 1.AREA 

AREA1 

2.MODE 

OFF 

3.MASK COLOR 

GREEN 

4.MASKTONE .. 

iiiiiiiiiiiiiii 1 

5.TOP n|iiiiiiii 

iiiiiiiiiiiiiii 39 

6 .BOTTOM .. 

iiiiiiiiiiiiiii 79 

7.LEFT "I. 

iiiiiiiiiiiiiii 13 

8 .RIGHT .. 

iiiiiiiiiiiiiii 52 

9.RETURN 4- 1 



18 


































USER’S MANUAL 


1) When the SPECIAL menu screen is displayed, press the Function Setup switch so 
that the arrow indicates 'PRIVACY'. 

2) Set up the mode using the Function Setup switch. 

-AREA: You can select up to 12 PRIVACY areas. 

- MODE: Determines whether to use the area selected in the AREA. 

- MASK COLOR: Determine area color. You can select Green, Red, Blue, Black, White, Gray. 

- MASK TONE: Adjust the brightness of MASK COLOR. 

- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area. 

- RETURN: Select this to save the PRIVACY menu settings and return to the SPECIAL menu. 

♦ MONITOR: 

Please change the settings value of video appropriate to your monitor. 

- LCD : Please select this menu item when using a LCD monitor. 

- CRT: Please select this menu item when using a CRT monitor. 

- USER: Please use this menu item when using a monitor other than standard ones. You can 
change the gamma, PED level, and color gain in the sub menus. 

♦ LANGUAGE : You can select the menu language according to your requirements. 

♦ RETURN : Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu. 

♦ Exit Setting 

Select a desired EXIT mode using the Function Setup Switch. 

- SAVE : Save the current settings and exit the MAIN SETUP menu. 

- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. 

- RESET: Resets the camera settings to the factory defaults. Language, Communication and 
Monitor Settings are not initialized. 


19 






USER’S MANUAL 


• Trouble Shooting 




PROBLEM 

POSSIBLE CAUSE 

Northing appears on 
the screen. 

"s^Check the power cable, power supply output and video 

connection between the camera and monitor. 

The image on the 
screen is dim. 

"s^Are the camera lens or the lens glass dirty? 

Clean the lens / glass with a soft clean cloth. 

"^Adjust the monitor controls, as required. 

^If the camera is facing a very strong light, change 
the camera position. 

“^Adjust the lens focus. 

The image on the 
screen is dark. 

“^Adjust the contrast control of the monitor. 

"ap|f there is an intermediate device, correctly set the 75Q/Hi-z. 

The camera is not 
working properly 
and the surface of 
the camera is hot. 

^Check the camera is correctly connected to an appropriate 

regulated power source. 

Motion Detection 

is not activated. 

^Has MOTION DET been set to ON in the menu? 

"a^Has MD AREA been properly defined? 

The color of the 
picture is not correct. 

"a^Check the settings in WHITE BALANCE menu. 

The image on the 
screen flickers. 

"a^Make sure that the camera isn’t facing direct sunlight or 
fluorescent lighting. If necessary,change the camera position. 

The SENS-UP does 

not work. 

"a^Check that the AGC setting in the EXPOSURE menu is’t set to OFF. 

"a^Check the EXPOSURE menu and make sure SHUTTER is set to—. 




20 






























USER’S MANUAL 


21